- 28 – 30% Stronger Metal
- 250% Longer Service Life
- 25 – 35°F Cooler Operating Temperatures
- Significantly Reduced Friction
- Acceleration and Top End Speed Gains
- Greatly Reduced Clutch Fade – almost to zero
- No Loss of Power at Wide Open Throttle
- At Least Double the Service Life on Every Engine Component After Processing
CryoHeat & Micropolish Single Cylinder Motorcycle
4-Stroke 50CC – 100CC : $499.96
4-Stroke 125CC – 500CC : $849.96
4-Stroke 501CC – 750CC : $949.96
CryoHeat & Micropolish Twin Cylinder Motorcycle
4-Stroke 500CC – 850CC : $999.96
4-Stroke 851CC – 1000CC : $1099.96
4-Stroke 1001CC – 2000CC : $1199.96
CryoHeat & Micropolish In-Line 4 Cylinder w/Trans
600CC – 750CC : $999.96
751CC – 900CC : $1049.96
901CC – 1100CC : $1149.96
1101CC – 1400CC : $1249.96
CryoHeat treating the entire transmission assembly has huge benefits; not only in 30% strength and 250% longer service life, but the dimensional stability is greatly enhanced as well. This keeps the shaft from flexing during any heavy torque load thus allowing more horsepower transferred to the rear wheel with less binding and friction. The CryoHeat Micropolishing changes the RA (Roughness Average) to a 2 RA or less. This makes the surface incredibly smooth and slippery. This enables the gears to move effortlessly from gear to gear and on the shafts without getting hung up. With the processing the transmission will have buttery smooth shifting and allows the shift dogs to engage quicker. An average increase of 2 hp is achieved with a CryoHeat and Micropolishing treated transmission.
Motorcycle transmission consists of all of the lower end drive gears; including crank gear, clutch gear, starter gears and all transmission gears. Primary shaft, counter shaft, shift shaft, shift drum, shift forks and shift fork posts.
CryoHeat & Micropolish Transmission
Sport Bike Transmission : $499.96
Also known as wet blasting or liquid honing, is rapidly becoming the number one choice for applications requiring the highest quality of surface finish. The key to vapor blasting is that the finish is produced through flow of water borne abrasive, giving a finer finish due to the flushing action of the water. No media is impregnated into the component, nor is there any dust created by the break-up of media, unlike dry blasting where the finish is produced by sheer force of media impact.
Magnetic Particle Inspection
CryoHeat uses Magnetic Particle Inspection for a non-destructive testing process. Easily detecting surface and shallow subsurface discontinuities in ferromagnetic materials such as iron, nickel, cobalt, and some of their other alloys.
The process puts a magnetic field into the part. The part can be magnetized by direct or indirect magnetization. Direct magnetization occurs when the electric current is passed through the test object and a magnetic field is formed in the material. Indirect magnetization occurs when no electric current is passed through the test object, but a magnetic field is applied from an outside source. The magnetic lines of force are perpendicular to the direction of the electric current.
The presence of a surface or subsurface discontinuity in the material allows the magnetic flux to leak, this occurs because air cannot support as much magnetic field per unit volume as metals can. To identify a leak, ferrous particles are applied to a part. These are attracted to an area of flux leakage and form what is known as an indication, which is evaluated to determine its nature, cause, and course of action, if any.
The CryoHeat Process makes the steel parts in the engine & transmissions 28-30% stronger, depending on the type of steel. Aluminum is 18-21% stronger. Service life is increased 250% or better, saving you repair time and money. The engine parts hold better dimensional stability and greater heat dissipation allowing them to run cooler during operation.
The CryoHeat Micropolishing Process speaks for itself! Once treated it has a 2 or less RA (Roughness Average) making the metal move faster than ever with almost zero friction and resistance. With the friction dramatically reduced you will experience little to no heat and drag which slows down the parts reducing the power from the engine. Faster speeds and power gains are achieved with this process. This is better than any coating or other surface treatment hands down! The micropolishing also promotes for even longer service life, cooler operating temperatures, less friction, and greatly aiding towards cleaner lubricant and sometimes showing zero wear on parts even after long term use. This is extremely important with high speed, high torque applications or anything that is going to be raced on and push to its limitations. Racing applications pick up miles per hour and tenths of seconds quicker quarter mile time just by micropolishing moving parts.
• 28 – 30% stronger metal
• 250% longer service life
• Removing burrs & machining blemishes
• Achieving an RA (Roughness Average) value of 2 or less (smooth as glass)
• Greatly reduces friction & drag allowing cooler temperatures during operation
Disassembly, Cleaning, & reassembly
Let our professional technicians disassemble, clean, and reassemble your project for a professional result. This process includes washing of the parts in 145 degree solution, then vapor blasting to remove any existing crud, and finally Magnaflux inspected to verify that there are no hidden stress cracks not visible with the naked eye before reassembling your project in our specifically designed clean room.
The CryoHeat treated forks and rear shock on a motorcycle work smoother with less friction and heat than anything else, including all coatings such as DLC, Nitrate, etc. More information coming soon or contact us with questions at firstname.lastname@example.org.
There are many other parts on a motorcycle or ATV that benefit from the CryoHeat process. Anything that needs to be stronger or have better wear resistance should be processed. Chains and Sprockets, even an aluminum sprocket, are significantly stronger and have almost 3x the service life after being CryoHeat treated. There are many other applications, such as kickstarter, shifter, brake pedal, clutch lever, hardware bolts, etc. Some of the endurance offroad racers are having us CryoHeat and Micropolish the wheel axles; this makes it much easier and faster to remove in a pit stop during the replacement of tires.